Oldest pages

Jump to navigation Jump to search

Showing below up to 50 results in range #21 to #70.

View (previous 50 | next 50) (20 | 50 | 100 | 250 | 500)

  1. RIE 1 (Custom)‏‎ (13:03, 13 June 2015)
  2. Surfscan6200 photos‏‎ (10:12, 12 April 2016)
  3. Thermal Evaporator 1‏‎ (17:31, 12 October 2017)
  4. ASML 5500: Recovering from a Typo in Reticle ID‏‎ (23:59, 20 March 2018)
  5. CDE ResMap Quick-Start instructions‏‎ (13:01, 17 April 2018)
  6. Unaxis Test Recipe Page‏‎ (15:19, 20 April 2018)
  7. InP Etch test -details‏‎ (08:43, 2 May 2018)
  8. InP Etch Test-in details‏‎ (08:57, 2 May 2018)
  9. TEST PAGE‏‎ (18:14, 18 June 2018)
  10. Thermal Evaporation Recipes‏‎ (17:00, 26 June 2018)
  11. ASML 5500: Choose Marks for Prealignment‏‎ (14:17, 17 July 2018)
  12. UV Ozone Quick Start‏‎ (15:40, 17 July 2018)
  13. Olympus LEXT OLS4000 Confocal uScope - Quick Start‏‎ (18:19, 25 July 2018)
  14. Lab Rules backup‏‎ (11:07, 3 August 2018)
  15. ProcessGroup: Shipping Samples on Dicing Tape+Frame‏‎ (17:27, 4 September 2018)
  16. Sputter 2 (SFI Endeavor)‏‎ (10:28, 5 September 2018)
  17. Test Data of etching SiO2 with CHF3/CF4/O2‏‎ (16:17, 8 October 2018)
  18. Ellipsometer (Rudolph)‏‎ (23:06, 10 October 2018)
  19. RIE5 - Standard Operating procedure (Cortex Software)‏‎ (14:09, 17 October 2018)
  20. ADT UV-Tape Table 1042R‏‎ (10:29, 22 October 2018)
  21. Suss MA-6 Backside Alignment QuickStart‏‎ (14:52, 28 November 2018)
  22. Stepper 2 (AutoStep 200) - Operating Procedure - Piece Parts‏‎ (11:12, 17 December 2018)
  23. Nano-Imprint (Nanonex NX2000)‏‎ (11:58, 18 December 2018)
  24. ADT 7100 - Recovering an Old Recipe (2019)‏‎ (03:15, 27 March 2019)
  25. Lab Rules OLD 2018‏‎ (15:26, 2 April 2019)
  26. Filmetrics F50 - Operating Procedure‏‎ (13:43, 26 April 2019)
  27. Test Page‏‎ (21:15, 16 May 2019)
  28. Filmetrics F40-UV Quick Start‏‎ (11:13, 31 May 2019)
  29. FIJI - Microscope Measurement Tools‏‎ (11:02, 10 June 2019)
  30. Intellemetrics Laser Etch Monitor Procedure for Panasonic ICP Etchers‏‎ (14:23, 13 June 2019)
  31. User Accessible Commands‏‎ (15:24, 13 June 2019)
  32. Stepper 1 (GCA6300) How to select proper chuck‏‎ (15:13, 20 June 2019)
  33. Stepper 1 (GCA 6300) Substrate Thickness, Shim Thickness ans Target Thickness‏‎ (15:32, 20 June 2019)
  34. Stepper 1 (GCA 6300) Available chucks‏‎ (15:41, 20 June 2019)
  35. Unaxis SiN100C 300nm-2019‏‎ (08:33, 10 September 2019)
  36. DS-K101-304 Bake Temp. versus Develop Rate‏‎ (14:02, 2 October 2019)
  37. SiN 100C Table-2019‏‎ (07:39, 3 October 2019)
  38. THz Physics Presentations‏‎ (13:59, 11 October 2019)
  39. Photonics Presentations‏‎ (09:04, 24 October 2019)
  40. Electronics Presentations‏‎ (15:17, 30 October 2019)
  41. PubList2018‏‎ (16:10, 27 November 2019)
  42. Older Publications‏‎ (16:30, 4 March 2020)
  43. Publications - 2013-2014‏‎ (16:34, 4 March 2020)
  44. Stepper 1 (GCA 6300) - Standard Operating Procedure‏‎ (09:42, 19 March 2020)
  45. Programming a Job‏‎ (10:36, 20 March 2020)
  46. GCA 6300 training manual -old instructions‏‎ (08:49, 23 March 2020)
  47. GCA Old full training manual‏‎ (09:58, 23 March 2020)
  48. Tino Sy‏‎ (11:26, 23 March 2020)
  49. Bill Mitchell‏‎ (11:32, 23 March 2020)
  50. Old training manual‏‎ (13:52, 23 March 2020)

View (previous 50 | next 50) (20 | 50 | 100 | 250 | 500)

Retrieved from "https://wiki.nanofab.ucsb.edu/wiki/Special:AncientPages"