Difference between revisions of "Template:Announcements"
Mehalana v (talk | contribs) |
Mehalana v (talk | contribs) |
||
| (10 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
<startfeed /> |
<startfeed /> |
||
| + | =====EBeam4 Update - Still down===== |
||
| ⚫ | |||
| + | EBeam4 will remain down overnight. |
||
| − | I will have to take the AFM head unit back to Bruker for repair. The height sensor failed all the tests I tried so the Z-piezo/strain gauge unit will most likely need to be replaced. SO for the foreseeable future, the AFM is down.--Demis |
||
| + | |||
| + | The new motor arrived as well as the new junction box and new cables. |
||
| + | |||
| + | I removed the old junction box/plugs due to a lot of corrosion inside the box caused by it being located directly under the water supply lines. |
||
| + | |||
| + | This corrosion inside the box could have contributed to the failure of the old motor. |
||
| + | |||
| + | I installed the new motor, ran all new cables to the new junction box in it's new location away from the water lines. |
||
| + | |||
| + | I was able to test the function of the hoist by raising and lowering the bell jar while in manual mode. |
||
| + | |||
| + | For safety reasons, I had the machine powered off during the duration of the work being done, so the cryo will be in regen overnight. |
||
| + | |||
| + | Tomorrow morning I will continue testing the system to ensure everything is working properly before I release the tool. |
||
| + | |||
| + | I will send another email when an update is available. |
||
| + | |||
| + | //10:36, 30 May 2024 (PDT) |
||
| + | |||
| + | =====Stepper #3 (ASML DUV) - System UP and calibrated===== |
||
| + | We have finished calibrations, |
||
| + | System is up. |
||
| + | |||
| + | Reminder to check/recalibrate your exposure dose. Focus should be the same, but beam optics changeout will affect dose. |
||
| + | |||
| ⚫ | |||
| + | |||
| ⚫ | |||
| + | Head was repaired and returned today. A quick test showed correct performance. Note also that the pin board has been repaired so all 4 pins are now present. Lets keep it that way so please be careful when loading the tip holder! |
||
| + | |||
| ⚫ | |||
| ⚫ | |||
=====MA6 TSA is down - Update===== |
=====MA6 TSA is down - Update===== |
||
| + | We have received the replacement motor for the TSA Y axis. The FSE will be onsite Monday June 3rd to work on the tool. |
||
| − | Still waiting on a quote and lead time for the board we need for the TSA microscope issue, was supposed to have that info yesterday. I've just pinged them and will provide everyone with an update once I have something. |
||
| + | |||
| + | The tool remains up for backside alignment and topside exposures that do not require alignment. |
||
| + | |||
| + | -Lee |
||
| + | //15:59, 22 May 2024 (PDT) |
||
| ⚫ | |||
=====Velion FIB Tool DOWN===== |
=====Velion FIB Tool DOWN===== |
||
Raith service are installing and aligning a new GaBiLi source. The Velion FIB column is not available to users until further notice. |
Raith service are installing and aligning a new GaBiLi source. The Velion FIB column is not available to users until further notice. |
||
//[[User:Mehalana v|Vraj Mehalana]] 10:58, 30 April 2024 (PDT) |
//[[User:Mehalana v|Vraj Mehalana]] 10:58, 30 April 2024 (PDT) |
||
| − | |||
| − | =====ASML optics replacement May 20th-22nd===== |
||
| − | We will be performing beam delivery optics replacement on Mon May 20th to 22nd, to resolve a low intensity reading. The tool will be unavailable during this time.e. |
||
| − | |||
| − | //[[User:Mehalana v|Vraj Mehalana]] 09:40, 9 May 2024 (PDT) |
||
=====ICP1 Down===== |
=====ICP1 Down===== |
||
| Line 23: | Line 52: | ||
=====Lab Access Changes: Symmetry App===== |
=====Lab Access Changes: Symmetry App===== |
||
| + | The iris scanner has been decommissioned. Please use the card reader which supports: |
||
| − | Card/Iris scanner access is still currently enabled. However we will be moving to a smartphone-based access system. '''IMPORTANT''': check your email to setup the new smartphone access system, so you will be ready when we switch to the new system. Look for an email titled '''''"Invitation to Access Symmetry App"'''''. |
||
| + | |||
| − | // [[User:John d|John d]] 13:49, 7 November 2023 (PST) |
||
| + | -Physical card |
||
| + | |||
| + | -Mobile phone via Symmetry App |
||
| + | |||
| + | //10:54, 23 May 2024 (PDT) |
||
=====Wafer Bonder, (Suss SB6-8E)===== |
=====Wafer Bonder, (Suss SB6-8E)===== |
||
Latest revision as of 10:36, 30 May 2024
EBeam4 Update - Still down
EBeam4 will remain down overnight.
The new motor arrived as well as the new junction box and new cables.
I removed the old junction box/plugs due to a lot of corrosion inside the box caused by it being located directly under the water supply lines.
This corrosion inside the box could have contributed to the failure of the old motor.
I installed the new motor, ran all new cables to the new junction box in it's new location away from the water lines.
I was able to test the function of the hoist by raising and lowering the bell jar while in manual mode.
For safety reasons, I had the machine powered off during the duration of the work being done, so the cryo will be in regen overnight.
Tomorrow morning I will continue testing the system to ensure everything is working properly before I release the tool.
I will send another email when an update is available.
//10:36, 30 May 2024 (PDT)
Stepper #3 (ASML DUV) - System UP and calibrated
We have finished calibrations, System is up.
Reminder to check/recalibrate your exposure dose. Focus should be the same, but beam optics changeout will affect dose.
//Vraj Mehalana 11:17, 24 May 2024 (PDT)
Atomic Force Microscope (Dimension ICON) - 05/17: System UP
Head was repaired and returned today. A quick test showed correct performance. Note also that the pin board has been repaired so all 4 pins are now present. Lets keep it that way so please be careful when loading the tip holder!
//Vraj Mehalana 13:46, 20 May 2024 (PDT)
MA6 TSA is down - Update
We have received the replacement motor for the TSA Y axis. The FSE will be onsite Monday June 3rd to work on the tool.
The tool remains up for backside alignment and topside exposures that do not require alignment.
-Lee //15:59, 22 May 2024 (PDT)
Velion FIB Tool DOWN
Raith service are installing and aligning a new GaBiLi source. The Velion FIB column is not available to users until further notice.
//Vraj Mehalana 10:58, 30 April 2024 (PDT)
ICP1 Down
The board we were waiting on arrived, but it did not resolve the tool issue. We are working with Panasonic on the next steps. //Vraj Mehalana 14:17, 1 March 2024 (PST)
Lab Access Changes: Symmetry App
The iris scanner has been decommissioned. Please use the card reader which supports:
-Physical card
-Mobile phone via Symmetry App
//10:54, 23 May 2024 (PDT)
Wafer Bonder, (Suss SB6-8E)
SUSS aims to be on site in early February. We’ll will send out an email once I get confirmation for a specific date. //Vraj Mehalana 14:23, 13 December 2023 (PST)